Bnc 1201 - 6 1/2 Digit Digital Multimeter Manuel d'utilisateur Page 73
- Page / 177
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
74
number of samples per trigger, the number of triggers per event, reading
hold, and the trigger delay for their measurements.
A. Number of samples on each trigger
By default, the multimeter takes only one reading on each trigger, but
you can instruct the multimeter to take specific number (up to 50000) of
readings each time it receives a trigger. The user’s input setting is stored
in a volatile memory which will be cleared after the meter has been
turned off and the default value will be restored. You can set the number
of samples on each trigger through front panel or the remote interface.
Front Panel Operation
Press MENU button and locate “TRIG” submenu by pressing ◁ and ▷
buttons. Press ENTER to choose “TRIG” option. Again locate “N SAMPLE”
submenu using ◁ and ▷ buttons and then press ENTER to select it.
Then set the desired number by pressing △and ▽ buttons to increase
or decrease the number, and using ◁ and ▷ buttons to move through
the digits. The locations of these buttons are shown with red rectangle
frames in Figure 4-11.
Procedures: MENU → TRIG → N SAMPLE →<Number>
Figure 4-11
Remote Interface Operation
Use the following command to set the number of samples from your PC
terminal.
+
- 6 ½ Digit Multimeter 1
- Table of Contents 2
- 1 General Information 5
- 1.2 Warranty Information 6
- Limitation of warranty 7
- 1.4 Upkeep of 1201 8
- 1.5 Safety Information 8
- 1.6 Symbols and Terms 9
- 1.7 Inspection 10
- 1.8 Options and Accessories 11
- 1.9 1201’s Dimension 12
- 2 Overview 13
- 2.2 Features 25
- 2.3.1 The Front Panel 25
- Upper Row Display 29
- Lower Row Display 29
- 2.3.3 The Rear Panel 31
- 3 Basic Measurement Function 33
- Figure 3-6 38
- Figure 3-7 38
- 3.6 Diode Measurements 41
- 3.7.2 RTD Measurements 44
- 4 Front Panel Operations 51
- 4.1.2 Filter 54
- 4.1.2.1 AC Filter 54
- 4.1.2.2 Digital Filter 55
- SENSe:AVERage:TCONtrol? 56
- 4.1.4 DC Input Resistance 59
- Measurements 64
- tCtBtAtRR 65
- 1 BtAtRR 65
- Thermocouple 66
- voltage for the selected 67
- 4.2 Trigger Operations 69
- 4.2.1 Trigger Mode 69
- 4.2.2 Trigger Source 71
- 4.2.3 Trigger Setting 72
- SAMPle:COUNt <value> 74
- TRIGger:COUNt <value> 74
- 4.3 Math Operations 77
- 4.3.1 Ratio 78
- 4.3.2 % (Percent) 79
- 4.3.3 Min/Max 80
- 4.3.4 Null 82
- 4.3.5 Limits Test 83
- (B) automatically. The 85
- 4.3.7 dB/dBm 86
- V is the relative reference 87
- 4.4.1 Display 90
- 4.4.2 Beeper 92
- SYSTem:BEEPer 94
- SYSTem:BEEPer:STATe {OFF 94
- 4.4.5 Scanning (Scan) 97
- (Fast 4.5) 0.02 99
- 4.4.6 Stepping (Step) 101
- 4.4.7 Initial Mode 102
- 4.4.8 Language 103
- 4.4.9 Error Condition 104
- 4.4.10 Firmware Revision 105
- 4.4.11 Calibration 106
- 4.4.12 Self-test 106
- Remote Interface Operations 111
- MEASure: 114
- STATUS REPORTING Commands 124
- Other Interface Commands 124
- IEEE-488.2 COMMON Commands 124
- 6 Error Messages 126
- 131
- (AC TRMS 134
- Current) 134
- B. General Specifications 135
- C.2 Output Data Formats 140
- C.3 The MEASure? Command 141
- C.4 The CONFigure Command 142
- C.7 The Triggering Commands 154
- IEEE-488.2 Common Commands 161
- TALK ONLY for Printers 163
DeLOCK 95232 manuals
Owner’s manuals and user’s guides for Hardware DeLOCK 95232.
We providing 4 pdf manuals DeLOCK 95232 for download free by document types: User Manual
Commentaires sur ces manuels